tag:blogger.com,1999:blog-7089240089080675728.post6879996745701886122..comments2020-04-16T06:48:49.420-07:00Comments on VOLKSWAGEN PASSAT: VOLKSWAGEN PASSAT 35I MK3 ABS TEVES MARK 2 BRAKE ANTI LOCK SYSTEM DEVICE.FRANK http://www.blogger.com/profile/05899055923323016216noreply@blogger.comBlogger5125tag:blogger.com,1999:blog-7089240089080675728.post-26675908322151213892018-02-17T05:34:18.146-08:002018-02-17T05:34:18.146-08:00My Teves 2 functions normally on my Corrado '9...My Teves 2 functions normally on my Corrado '94, but when I press the brake pedal (very) quickly, It does not engage, so I get hard braking and only on the front brakes. I replaced the original system by one from a '94 Passat.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-7089240089080675728.post-26953459410916534222017-05-19T22:38:01.830-07:002017-05-19T22:38:01.830-07:00I have a 1990 Corrado G60 (same Teves 02 ABS) but ...I have a 1990 Corrado G60 (same Teves 02 ABS) but cannot read out ABS errors. ABS and BRAKE lights never go out, I have no working ABS but I have brake pressure (no hard pedal) I have checked the 4 wheel sensors voltage, the ABS relay, the ABS fuse but not sure what to look at next?<br /><br />Is the system worth sending out for remanufacturing? Convert to non-ABS?Anonymoushttps://www.blogger.com/profile/17563934501923021117noreply@blogger.comtag:blogger.com,1999:blog-7089240089080675728.post-4938897897134415582013-11-17T10:34:22.891-08:002013-11-17T10:34:22.891-08:00thank you for decrribing of ABS system
thank you for decrribing of ABS system<br /><br />Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-7089240089080675728.post-25092909579667013322013-09-30T11:45:01.912-07:002013-09-30T11:45:01.912-07:00Hi,
The error code 1222 is related to Main valve....Hi, <br />The error code 1222 is related to Main valve.<br /><br />The main valve is intended for enabling the main idraulic functions of the Idraulic unit.<br /><br />The main solenoid valve is always active with ABS controlled braking. It<br />switches the accumulator pressure directly to the inlet and outlet solenoid<br />valves by way of the collars of the brake master cylinder (collar overflow). In<br />accordance with the lock-up tendency, pressure holding, pressure reduction or<br />pressure build-up is implemented at the respective wheel brake cylinders by<br />way of the inlet and outlet solenoid valves.<br /><br />Malfunctioning may be a stuck valve or a broken electric solenoid circuit of the valve.<br /><br /><br /><br />SELF-DIAGNOSIS FLASHING CODE 1222:<br /><br />CHECKINGS to do :<br /><br />Main valve,<br />- Ignition off.<br />- Pull plug off controller.<br />- Check solenoid valve resistance at<br /> controller plug. X1 term. 11 -> X1 term.18<br />Set value: 2...5 Ohm<br /><br />- Check solenoid valves and leads for short to ground/short to positive, open<br />circuit and loose contacts as per circuit diagram.<br /><br />- Check contacts of connectors.<br /><br />NOTE: The ABS is a vehicle safety system.<br />Work on this system presupposes detailed system knowledge.<br />Testing may only be performed by trained personnel.<br /><br />After loosening hydraulic connections, bleed brake system and perform low-<br />pressure as well as high-pressure test.<br />Pay attention to special bleeding specification.<br /><br />You have to contact a skilled and trained personal to do deep diagnosing or <br />things may go even worse.<br /><br />FRANK.<br />FRANK https://www.blogger.com/profile/05899055923323016216noreply@blogger.comtag:blogger.com,1999:blog-7089240089080675728.post-71010331833027267492013-09-28T02:41:42.926-07:002013-09-28T02:41:42.926-07:00Hello
I have a Passat 35i with a problem in the br...Hello<br />I have a Passat 35i with a problem in the braking system.<br />Some time ago started a few times the vacuum motor does not work. Was co very hard and pedal the oil level indicator/hand brake, always connected. Even when the engine works, this light goes on and off every time you brake.<br />I went to investigate and found that: the mains pressure valve (5 pins) was oxidized.<br />In addition, also the abs indicator lamp was blown.<br />I cleaned the plug valve, vacuum problem disappeared, and replaces the abs lamp.<br />Now whenever brake, continues to show the oil level indicator light/Handbrake (correct oil level), and the abs light comes on. I've done the test and it gives me the error 1222. <br />Does your experience can help me?<br />In advance grateful<br />PS: excuse my English (Translito)A.Lourençonoreply@blogger.com